Installing flexiWAN

Overview

This section covers installing flexiWAN using the Installation image, recommended for baremetal installation. If you’re interested in virtualizing flexiWAN, several pre-built virtual appliances are available.

Before continuing, make sure to download the ISO image from the Getting & Installing flexiWAN. section. Also, make sure your hardware satisfies the system requirements.

Follow these steps to sucessfully install flexiWAN on your hardware:

  • Write the image to USB
  • Boot from USB and install flexiWAN
  • Complete the installation.

Writing image to USB

After downloading flexiWAN installer image, the next step is to write the image to USB.

To write image on Windows, download Rufus from here. After downloading Rufus, plug in the USB disk drive, select flexiEdge ISO and click on Start to write the image to the USB. Keep all other option defaults.

Rufus

After the flexiEdge is written to USB, proceed to the next section, Installing flexiWAN.

Installing flexiWAN

Once the flexiEdge installer USB drive is ready, the next step is to plug in the drive to your device and turn it on. Make sure USB is selected to boot first.

At GRUB selection offers selecting monitor output and serial. For this guide we’ll use monitor output however procedure is the same for serial.

Iso 1

After a few moments installer wizard will show. Click OK to continue.

Iso 2

Accept EULA in order to continue installation.

Iso 3

Setup will automatically detect available hard drive and offer installing to it. Simply click OK and that’s it, installation wil start.

Iso 4

Wait for a few moments until setup completes. The installer will create main partition and recovery partition. Recovery partition is useful for offline reinstallation.

Iso 5

Upon completion, setup will automatically reboot the device. Make sure to unplug USB and boot from the internal disk drive.

Iso 6

That’s it, flexiWAN is now installed! Default username and password are: admin / flexiwan

Iso 7

After sucessfully installing flexiWAN to your device, proceed to “Checking your system configuration” section below.

System checker

System checker is a post installation system check utility. It makes sure system requirements are met and prepares the device for flexiWAN operation.

System Checker from flexiEdge UI

With the latest versions system checker is integrated to and available from the flexiEdge UI, a local web interface for initial configuration and troubleshooting. To access it, simply navigate to the device IP and port 8080.

Example: HTTP://192.168.100.10:8080/

After opening the flexiEdge UI page, enter username and password from Linux.

EdgeUI

After logging in, click on System Checker page and run it to check if the system meets the requirements.

system checker

If installed on supported hardware, in most cases there will only be “soft” failures which can be fixed by clicking on “Auto-fix”:

system checker

Confirm the output now says system requirements are met proceed to the Device Mangement section, starting with token creation and installation steps as described in the following flexiManage section.

System Checker from the command line

System checker is also available from the command line for a faster deployment or for advanced configuration.

Run the fwsystem_checker tool to pass system requirements and fix software configuration errors. After installing the flexiEdge software, execute the following as root:

fwsystem_checker

The system checker utility will analyze your system hardware, host OS software configuration and output the results. For flexiEdge software to work properly, it’s important to pass all hardware related checkes, while most of soft-fail checks are fixed easily.

System checker

After running system checker there will likely be a few soft configuration fails, which can be fixed in automated or interactive way. System checker offers an automated way to fix all soft fails and prepare the system for flexiWAN operation. It also offers an interactive mode where each setting can be manually configured by the user.

Running system checker with default settings

To fix software configuration issues silently and automatically using defaults, run the fwsystem_checker utility and select the following options:

  • 2. Configure system silently - to configure system without interaction using defaults
  • 1. Check system configuration - to verify issues are resolved
  • 0. Quit and use fixed parameters - to save the settings and exit utility.
System checker

Running system checker interactively

An interactive system configuration is also available, chosing this option will allow detailed configuration and enable advanced features such as multi-core support and CPU power saving. If your device has multiple WAN interfaces and gateways, selecting this option will allow choosing the default gateway, among other options.

To fix software configuration manually and interactively, choose the following:

  • 3. Configure system interactively follow the wizard to configure every step manually.
System checker 2

Last option in system checker, under number 4 is - “Restore system checker settings to default”. Use this option if you wish to remove all configuration done with silent or interactive steps. Reboot is required after restoring system to factory defaults.

System checker 3

After passing all hard and soft checkes, proceed to Device Mangement section, starting with token creation and installation steps as described in the following flexiManage section. In order to access flexiManage, please create an account.